Want to know how to drain a Bunn coffee maker? If so, you have come to the right place! Here is a list of steps that will allow you to do this effectively and quickly:
Draining a Bunn Coffee Maker
Step 1: Unplug the Bunn Coffee Maker
As you are aware, electricity and water should never mix. Due to this, your first step should involve unplugging the Bunn coffee maker. Not only will this make the procedure safer, but it will also ensure that you can move the Bunn coffee maker to a spot that allows you to drain it properly.
If the plug of the coffee maker gets wet at any point during this process, make sure to dry it off thoroughly with a paper towel. It is also a good idea to wait a few hours before plugging the coffee machine into a power source again.[powerkit_posts title=”Related Reading” count=”1″ offset=”0″ image_size=”pk-thumbnail” category=”” tag=”” ids=”964″ orderby=”date” order=”DESC” time_frame=”” template=”list”]
Step 2: Clean the Carafe
You will be using the carafe for the next step of the process. As a result, it needs to be clean. If you have brewed coffee earlier that day, wash it out thoroughly. It should be dry and not contain any coffee dregs or residue.
You will be using the carafe to fill up the hot water tank. If there is any debris in the carafe, this can enter the hot water tank and may clog up the coffee maker. To prevent this from happening, clean out the carafe thoroughly.
Step 3: Flush Out the Hot Water
Needless to say, draining hot water isn’t a good idea. Due to this, it needs to be flushed out before you can focus on draining the coffee maker.
Fill the carafe with cold water – tap water will work. Open the lid of the hot water tank and pour it in. Replace the carafe on the hot plate and close the lid.
Once you do this, the cold water will begin to push the hot water out of the tank and into the carafe. Wait until you can’t see any more water flowing into the carafe. Then, empty the carafe.
You will need to repeat this process. This is the only way to be certain that all the hot water in the tank is gone. Once again, fill the carafe with cold water and pour it into the hot water tank. Replace the carafe and wait for all the water to drain out.
After pouring in the water a second time, it is a good idea to test the temperature of the water. Be careful as you can’t tell how hot it might be.
Gently place your hand against the carafe to see if it is hot to the touch. Or, you can use a spoon to scoop out some water from the carafe. Dip your finger into the water to determine this.
If the water still feels quite hot, you may need to repeat the process. Do this until the water is either lukewarm or cool.
Step 4: Remove the Brew Funnel and Spray Head
The brew funnel and spray head will probably get in the way during this process. Make it a point to remove these pieces ahead of time. Once you have done so, set them aside. If you have just used them to brew coffee, it is a good idea to clean these pieces. Follow the instructions provided in your owner’s manual.[powerkit_posts title=”Related Reading” count=”1″ offset=”0″ image_size=”pk-thumbnail” category=”” tag=”” ids=”936″ orderby=”date” order=”DESC” time_frame=”” template=”list”]
Step 5: Draining the Coffee Maker
Pick up your Brew coffee maker with both hands. Make sure that the wire and the plug are out of the way. You can coil it and hold the wire so that it is tucked behind the coffee maker.
Once you do this, move the coffee maker to your sink. You can also choose to do this above a large, deep bowl. However, a sink should work better.
Then tip your coffee maker at an angle over the sink. This will cause the water to begin flowing out of where the spray head was. However, don’t worry if some water comes out of the lid.
Continue holding the coffee maker in this position until water stops flowing out. You may want to hold the coffee maker over the sink for a few minutes after the water has stopped to make sure that you get all the water out.
Put the coffee maker back on the counter once you are done.
Step 6: Replace the Brew Funnel and Spray Head
Place the spray head back into its original position and turn clockwise until you are certain that it has been fixed into place. Then, replace the brew funnel. If you are transporting your coffee maker, it is a good idea to wipe down the brew funnel first. This will ensure that there is no moisture trapped inside.
Then put the brew funnel back into its original spot and press until it snaps back into place.
Tips to Remember
There are a few things to keep in mind before starting on this process.
Firstly, follow the steps as instructed for the best results. For instance, don’t simply tip over the coffee maker without removing the hot water first. Sure, you may save some time, but you could also end up scalding yourself – why take the risk?
Each Bunn coffee maker model is different. So, when in doubt, it is always a good idea to read your instruction manual. This will offer more precise instructions.
If you have lost the manual, check the model number of the machine. Then, look for the manual online. In case you can’t find one, simply email the manufacturing company. They will be able to provide you with the exact model you’re looking for.
If the coffee maker seems too bulky or heavy for you to handle, make sure to get some help. After all, you don’t want to end up dropping the machine. If you are handling the process by yourself, make sure to pick up and hold the machine with both hands at all times.[powerkit_posts title=”Related Reading” count=”1″ offset=”0″ image_size=”pk-thumbnail” category=”” tag=”” ids=”941″ orderby=”date” order=”DESC” time_frame=”” template=”list”]
When to Drain a Bunn Coffee Maker
When should you be draining a Bunn maker? Well, there are a couple of reasons why you may want to do this.
The first is if you are preparing on leaving your Bunn coffee maker unused for some time. Perhaps you are traveling out of town or going on vacation. In this case, you will need to remove all the water stored inside. Otherwise, the risk of mold, bacteria, and other issues cropping up increases.
Another reason you may want to drain the coffee maker is if you are planning on transporting or shipping it. In transit, there is always a chance that the water in the coffee maker can spill. Not only will this cause a mess, but it may end up damaging certain parts of your coffee maker as well.
To prevent either of these scenarios, it can be helpful to know how to completely drain your coffee maker to keep it in good condition.
This is what you need to know about draining your Bunn coffee maker. Just follow the instructions provided here and you will be able to empty the coffee machine in no time at all.